Renegade CJ
- Thread starter matth_85
- Start date
Been driving it around the block a time or two every afternoon this week.
Dash is finished. New windshield yesterday. Brakes are much improved. Rear shocks seem to be charged properly. May add a little to the front after I drive it a good bit more.
Very short to-do list now:
Bleed rear brakes some more
Finish up the switch panel for fan and winch
Final nut-bolt check
Dash is finished. New windshield yesterday. Brakes are much improved. Rear shocks seem to be charged properly. May add a little to the front after I drive it a good bit more.
Very short to-do list now:
Bleed rear brakes some more
Finish up the switch panel for fan and winch
Final nut-bolt check
Me and @jimbo92 made the Gulches run today. Overall happy with the Jeep. Have a couple of things to work on before we leave.
Brakes...work but don’t hold a steep incline in 4-low. I assumed this would be the case. Should be able to get them good.
Engine temp. It never got above 210* and we rode for around an hour to an hour and a half I think. However I didn’t love the temp....going to pick up a pusher fan to wire on a switch tomorrow. I also ordered the Poison Spyder hood lovers this week and they will be here Tuesday so I’m going to install those for sure. That should fix that...
Driveshaft hits the lower link mount at a certain flex/off camber point. Nothing to see here. Move along.
Brakes...work but don’t hold a steep incline in 4-low. I assumed this would be the case. Should be able to get them good.
Engine temp. It never got above 210* and we rode for around an hour to an hour and a half I think. However I didn’t love the temp....going to pick up a pusher fan to wire on a switch tomorrow. I also ordered the Poison Spyder hood lovers this week and they will be here Tuesday so I’m going to install those for sure. That should fix that...
Driveshaft hits the lower link mount at a certain flex/off camber point. Nothing to see here. Move along.
Did a lot of brake bleeding tonight. If you’ve been to Jim’s house you know he’s got the steepest hill in greenwood at his driveway. It held 4-low and would stop 4-low on that. That is a great feeling!
New K&N and pre-filter for that sand yo!
And most importantly, my tag came in.
Tomorrow I have to put the hood louvers on and do some cleaning up and nut/bolt check.
Wednesday I’ll load everything up and be ready for an early morning departure.
New K&N and pre-filter for that sand yo!
And most importantly, my tag came in.
Tomorrow I have to put the hood louvers on and do some cleaning up and nut/bolt check.
Wednesday I’ll load everything up and be ready for an early morning departure.
After 7 days of wheeling in all conditions the CJ held up extremely well. It had just over 140 miles on it when it hit the trailer and only about two hours of trail time. I'll have to check the trip meter but I think we logged about 175 miles of trail/road time over the adventure. Heay on the trail time because we towed to all Moab trail heads. The only failure I had was a fuel pump which was already on the fritz. It did not like the long climbs in the higher temps but I think that will be a fairly easy fix.
Very happy with the outcome and performance.
Now to clean it up good, nut/bolt check, and do some finish work I didn't get to before we left.
Very happy with the outcome and performance.
Now to clean it up good, nut/bolt check, and do some finish work I didn't get to before we left.
Got the fenders fixed today. The fender was hanging the tire and bending it out. I straightened them back up and reworked the support bar allowing me to tack the fender to the bar. Should be rigid enough to keep the tire from tearing it up now.
Nut and bolt check this week and hopefully headed to Windrock next weekend.
Nut and bolt check this week and hopefully headed to Windrock next weekend.